Thursday, January 15, 2015

Philco PFS2108 TV Service Menu

Philco PFS2108 TV Service mode Adjustment-1
Enter to sanyo factory menu
While pressing the MENU button on the television, press the Number Key 2 on the remote control unit.
The Service Menu now appear.

Service Adjustments:
Press the CHANNEL UP or CHANNEL DOWN button on the remote control handset to select the
desired service menu item you want to adjust. Use the VOLUME + or - to adjust the data. The + or
- button will increase or decrease the data sequentially.

Exit from the factory mode
Press the MENU button to turn off the Service Menu display.
The data which is set in the service mode is stored into the memory IC automatically.

Item 01 [RFAGC] AGC
NOTE: Do not attempt this adjustment with weak signal.
1. Tune the receiver to most clearest (or strongest) VHF station in your area. Set the brightness and contrast
controls to maximum. Set the colour control to minimum.
2. Select Item No. 01 [RFAGC] in the service mode.
3. Change value until the snow noise just disappears.
4. Exit from the service mode.3

Item 04 [V-SIZ] VERTICAL SIZE
1. Receive a monochrome circular pattern.
2. Set the brightness and contrast to maximum.
3. Select Item No. 04 [V-SIZ] in the service mode.
4. Change value to be optimum vertical size.
5. Exit from the service mode.

Item 02 [H-PHA] HORIZONTAL CENTRE
1. Receive a monochrome circular pattern.
2. Set the brightness and contrast to normal.
3. Select Item No. 02 [H-PHA] in the service mode.
4. Change value to be optimum horizontal centre position.
5. Exit from the service mode.

Item 12 [OSDHP] OSD POSITION
1. Receive a monochrome circular pattern.
2. Set the brightness and contrast to normal.
3. Select Item No. 12 [OSDHP] in the service mode.
4. Change value to be proper OSD position.
5. Exit from the service mode.

Item 95 [CCD] CAPTION H-POSITION ADJ.
1. Tune receiver to a caption channel.
2. Check that CAPTION position is in the horizontal
center of the screen. If CAPTION center is too right or
left, perform steps 3-6. (See figure below.)
3. Select Item No. 85 [CCD] in the service mode.
4. Adjust data with + or - key for proper horizontal center.
5. Exit from the service mode.

Item 15 [VSHIFT] VERTICAL CENTRE
1. Receive a monochrome circular pattern.
2. Set the brightness and contrast to maximum.
3. Select Item No. 15 [VSHIFT] in the service mode.
4. Change value to be optimum vertical centre position.
5. Exit from the service mode.

Philco PFS2108 TV Service mode Adjustment-2
Service Adjustment-2 (MTS
1. Enter the Service Menu While pressing the MENU button on the television, press the “3” or MENU button on the remote control unit. The Service Menu now appear.
VOLUME OFFSET 07
TREVLE OFFSET 04
BASS OFFSET 04

2. Service Adjustments:
Press the CHANNEL UP or CHANNEL DOWN button on the remote control handset to select the
desired service menu item you want to adjust. Use the VOLUME + or - to adjust the data. The + or
- button will increase or decrease the data sequentially.

3. Exit from the Service Menu
Press the MENU button to turn off the Service Menu
display.
The data which is set in the service mode is stored
into the memory IC automatically.

TV Service mode Philco PFS2108
Photo by trend-kid.com

Philco PFS2108 TV Service mode
Do not attempt to Philco TV service adjustments not listed on below otherwise it may cause loss of performance and for correct operation.

3leex Media Online

  • Blogger Comments
  • Facebook Comments

0 comments :

Post a Comment

Item Reviewed: Philco PFS2108 TV Rating: 4.3 Reviewed By: eLX Elcideed

Service mode

Sanyo

Samsung

Konka