Tuesday, January 13, 2015

Konka K2073UM TV Service Menu

Factory mode for Konka TV model K2173PM, K1473PM, K2073UM, K1373UM & K1306UM
Press MUTE, TIMER, PICTURE buttons continuously in two seconds to enter
into factory menu.
Press P+, P- buttons to select the item to adjust.
Press VOL+、VOL- buttons to adjust the selected item or enter into the submenu.
Press MENU button to return the super menu.
Under main menu mode, press MENU button to exit factory menu.
Factory menu settings please see the following: (* marked before the item
presents adjustable item, and the value in the bracket is default value)

TV Service mode Konka K2073UM
Photo by imgarcade.com

IMPORTANT SERVICE SAFETY
Operating the receiver outside of its cabinet or with its back removed involves a shock hazard. Work on these models should only be performed by those who are thoroughly familiar with precautions necessary when working on high voltage equipment.
Exercise care when servicing this chassis with power applied. Many B plus and high voltage RF terminals are
exposed which, if carelessly contacted, can cause serious shock or result in damage to the chassis. Maintain
interconnecting ground lead connections between chassis, escutcheon, picture tube dag and tuner when operating chassis.
These receivers have a “polarized” AC line cord. The AC plug is designed to fit into standard AC outlets in one direction only. The wide blade connects to the “ground side” and the narrow blade connects to the hot “side” of the AC line. This assures that the TV receiver is properly grounded to the house wiring. If an extension cord must be used, make sure it is of the “polarized” type.
Since the chassis of this receive is connected to one side of the AC supply during operation, service should not be attempted by anyone not familiar with the precautions necessary when working on these types of equipment.
When it is necessary to make measurements or tests with AC power applied to the receiver chassis, an Isolation Transformer must be used as a safety precaution and to prevent possible damage to transistors. The Isolation Transformer should be connected between the TV line cord plug and the AC power outlet.
Certain High voltage (HV) maybe cause X-ray radiation. Receivers should not be operated with HV levels exceeding the specified rating for their chassis type. Higher voltage may also increase the possibility of failure in the HV supply.
It is important to maintain specified values of all components in the horizontal and high voltage circuits and anywhere else in the receive that could cause a rise in high voltage, or operating supply voltages. No changes should be made the original design of the receiver.
Components shown in the shaded areas on the schematic diagram and/or identified by in the replacement parts list should be replaced only with exact factory recommended replacement parts. The use of unauthorized substitute parts man creats may create shock, fire, X-ray radiation, or other hazards.
To determine the presence of high voltage, use an accurate high impedance HV meter connected between the second anode lead and he CRT dag grounding device. When servicing the High Voltage System remove static charges from it by connecting a 10K Ohm resistor in series Wan insulated wire(such as test probe) between the picture tube dag and 2nd anode lead(Have AC line cord disconnected from AC supply).
The picture tube use in this receiver employ integral implosion protection. Replace with a tube of the same type number for continued safety. Do not lift picture tube by the neck. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage completely, Keep others without shatter proof goggles away.
Before returning the receiver to the user, perform the following safety checks:
1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver.
2. Replace all protective devices such as non-metallic control knobs, insulating fishpapers, cabinet backs,
adjustment and compartment covers of shiedls, isolation resistor-capacitor networks, mechanical insulators etc.
3. To be sure that not shock hazard exists, a check for the presence of leakage current should be made at each exposed metal part having a return path to the chassis (antenna, cabinet metal, screw heads knobs and/or shafts,
escutcheon, etc.) in the following manner.
Plug the AC line cord directly into a 120V, AC receptacle. (Do not use an Isolation Transformer during these
checks.) All checks must be repeated with the AC line cord plug connection reversed. (If necessary, a nonpolarized

3leex Media Online

  • Blogger Comments
  • Facebook Comments

0 comments :

Post a Comment

Item Reviewed: Konka K2073UM TV Rating: 4.3 Reviewed By: eLX Elcideed

Service mode

Sanyo

Samsung

Konka